Top 10 typical forklift accidents ， forklift operation must pay attention to these matters ！.
Top 10 typical forklift accidents ， forklift operation must pay attention to these matters ！.
Blog Article
Don't ignore the forklift at the workplace. If the operation is not good, there will be major mishaps in mins, and there are several crashes entailing forklifts.
Instance 1: The forklift freight obstructed the driver's sight, and the person in front could not be found, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which practically causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the employees illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure should take note of these issues ：.
Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge must be secure before beginning.
3. When the forklift begins with a load, the vehicle driver should first validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.
Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the mast needs to be tilted in reverse. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the lots is traveling, the fork needs to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be released first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to lose side stability and topple. .
5. When the forklift is downhill, it is purely forbidden to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load will not be elevated other than when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In special conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported Electric Forklift Truck for Warehouse in a prompt manner, and they will certainly never ever operate with illnesses or hide them.
packing and unloading.
1. When fork-loading things, the distance in between both forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or utilize a fork top or pull. In unique situations, safety indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the vehicle must be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork pointer should not touch various other items or objects. The tons should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.
Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for unique conditions, such as the vehicle driver does not leave the vehicle's view and does not go beyond 1 min).
4. Eliminate the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and cooling water should be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be examined and the seals must be replaced in time.
Forklift Safety Operation Specifications.
1. You must examine prior to leaving the cars and truck;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they come across huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal Stand-on Electric Pallet Stacker with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844